|
Title: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 16, 2008, 06:31:18 AM Well I finally got my Header for my '95 SS but I need to find some plugs for the threaded
Lambda probe holes . does anyone have any suggestions how I can plug them up?? I thought about removing the ones from the stock header but have a feeling it will be difficult to remove can't wait to put this header on I was surprised at how little it weighed [laugh] Dan......... :o Title: Re: Sil-Moto header Post by: brad black on October 18, 2008, 04:00:44 AM if they're the small std ones the thread is a 1/8 npt or gas, straight not tapered. it's almost m10 x 1, but not quite.
if you're talking about what a normal lambda sensor goes into they're m18 x 1.5, which is the same as many european car sump plugs - wurth sell them as sump plugs. Title: Re: Sil-Moto header Post by: weemonster on October 18, 2008, 10:50:11 AM pics please i'd like to see your sil header.
Title: Re: Sil-Moto header Post by: dansamp on October 19, 2008, 10:03:52 PM (http://img408.imageshack.us/img408/7523/img0483nr4.th.jpg][/url])
well I have uploaded photos to image shack but am too stupid to post them here WAAAAAAA !!!!!!!!!!! Title: Re: Sil-Moto header Post by: dansamp on October 20, 2008, 06:18:45 AM (http://img408.imageshack.us/img408/7523/img0483nr4.jpg)
Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 20, 2008, 06:21:26 AM couple more :
(http://img522.imageshack.us/img522/7696/img0489pb1.jpg) (http://img252.imageshack.us/img252/7560/img0482tw4.jpg) (http://img413.imageshack.us/img413/5361/img0487pz6.jpg)] Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 20, 2008, 06:29:48 AM This is with the DP high mount cans
I will install my N.I.B. set of high mount Termi's once I get the carbs readjusted and dyno'd [thumbsup] Dan.......... I am a little worried at how close the pipe is to the crankcase it seems to touch in two places I have e-mailed this concern to Mark at eurocorsa but have not heard back yet anyone have any thoughts on this ??? Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Jarvicious on October 20, 2008, 07:36:29 AM I am a little worried at how close the pipe is to the crankcase it seems to touch in two places It's definitely way too close. I think you're going to have overheating issues, as well as metal fatigue in all the load bearing members along with the possibility of excess wear in your strut mounted manifold dampening indicators. My custom, one-off, pre-fabbed, liquid cooled crank case has an indention built specifically for these headers. I wouldn't have a problem taking them off your hands and testing them while you figure out another solution, just let me know. Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Drunken Monkey on October 20, 2008, 03:14:40 PM These headers are a PITA.
I could not get mine to fit correctly and finally broke down and had an extra few inches added to the V-cylinder pipe. We'll see later this week if it fixes the problem... Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 20, 2008, 03:28:56 PM Drunken Monkey,
do you have any measurements ?? I am thinking if the front pipe that goes under the crankcase was more horizontal that might be better if you extended the rear cylinder longer then you will lose some ground clearance and possiblely fairing clearance if you have a full fairing Mark at Eurocorsa forwarded my pics to Sil-Moto so hopefully they will respond hope it works I would hate to have to get the full Termi set for 4k :P Dan........... Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: El Matador on October 20, 2008, 03:56:07 PM damn that bike looks good!
Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Howley on October 20, 2008, 04:08:12 PM Damn you and your MBP heads!
Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 21, 2008, 02:06:48 PM Yeah !!!
don't forget the ST2 cams with adjustable pulleys and the short Mallossi manifolds and 41mm FCR's ;D pumping out 97 HP to the rear wheel !!! I am hoping to get over 100 HP with the header [thumbsup] Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Cider on October 21, 2008, 02:48:10 PM I agree: super-cool bike.
Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Howley on October 21, 2008, 03:37:55 PM Yeah !!! don't forget the ST2 cams with adjustable pulleys and the short Mallossi manifolds and 41mm FCR's ;D pumping out 97 HP to the rear wheel !!! I am hoping to get over 100 HP with the header [thumbsup] Yeah damn all that too... Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 21, 2008, 04:25:13 PM Yeah damn all that too... oh yeah, I almost forgot 944 big bore kit ........... I could have bought a 1098 :o :o NAHHHHHHHH Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: Howley on October 22, 2008, 02:10:41 PM Showoff. I want your bike, give it to me.
Title: Re: Sil-Moto header (With Pics-FINALLY !!!!!!!!! ) Post by: dansamp on October 23, 2008, 07:14:16 AM OK,
update on the clearance issue I stopped by West coast GP cycles yesterday and spoke with Andy he said I should have no problem with the pipe touching the crankcase he said he has a bike he has raced for 3 years what also has the pipe touching the crankcase and has not had any issues with it I even asked about wrapping that part of the pipe but he said don't worry about it so it's off to the dyno [cheeky] I am going to install the Termi's and post some more pics Dan.............. |