Can anyone tell me what size and pitch tap is needed clean out the clutch basket holes?
I definately don't have it in my set and I would prefer not to buy a whole new set.
Thanks in advance!
I think they're 8 x 1.25.
But don't quote me.
Quote from: ducpainter on February 12, 2009, 07:37:45 PM
I think they're 8 x 1.25.
But don't quote me.
OOPS!
Can anyone confirm?
Quote from: gage on February 12, 2009, 07:43:54 PM
OOPS!
Can anyone confirm?
I checked the torque thread in tutorials...
clutch drum screws....8 x 1.25
The new used basket I have has clearance holes for an 8mm screw.
1.25 is the only 8mm pitch Duc uses....
take a chance...
Columbus did.
Ok I guess your logic makes sense [roll]
Thanks [thumbsup]
Quote from: gage on February 12, 2009, 07:55:12 PM
Ok I guess your logic makes sense [roll]
Thanks [thumbsup]
fume induced.... ;)
Yup, I "think" dicpainter is right. As I recall, they don't take as much torque as you'd think.
Quote from: Norm on February 13, 2009, 07:09:57 AM
Yup, I "think" dicpainter is right. As I recall, they don't take as much torque as you'd think.
Wow! That's a whole new profession I wasn't aware of
Quote from: Norm on February 13, 2009, 07:09:57 AM
Yup, I "think" dicpainter is right. As I recall, they don't take as much torque as you'd think.
Some history dies hard.... ;D
Quote from: gage on February 13, 2009, 09:47:56 AM
Wow! That's a whole new profession I wasn't aware of
I'll paint any make the beast with two backsing thing. [laugh]
Isn't it nice to have people who still know how to say "I think" or "I'm not sure"? I've seen people answer questions on this board with absolute authority when I KNOW there are wrong. Of course they belong to the motorcycle "god" club that CAN'T be wrong. Please shoot me if I ever get that arrogant.
Quote from: Norm on February 14, 2009, 08:04:59 AM
Isn't it nice to have people who still know how to say "I think" or "I'm not sure"? I've seen people answer questions on this board with absolute authority when I KNOW there are wrong. Of course they belong to the motorcycle "god" club that CAN'T be wrong. Please shoot me if I ever get that arrogant.
Quit sucking up! You called Nate "dicpainter," and we're all witnesses!!
;D [laugh]
Quote from: pompetta on February 14, 2009, 01:07:55 PM
Quit sucking up! You called Nate "dicpainter," and we're all witnesses!!
;D [laugh]
most just call me dic...
at least he used my last name.. ;D
You don't have anything freaky planned for DIMBY, do you?
Quote from: ducpainter on February 12, 2009, 07:37:45 PM
I think they're 8 x 1.25.
But don't quote me.
They are indeed 8mm x 1.25 [thumbsup]
Thanks Guuys
oops, I just saw the mispell - sorry Ducpainter [bow_down]
Typing and spelling aren't my specialty.
Quote from: Norm on February 15, 2009, 06:45:50 AM
oops, I just saw the mispell - sorry Ducpainter [bow_down]
Typing and spelling aren't my specialty.
not to worry Norm. [thumbsup]
don't over-torque them, btw...they're like 20ish ft/lbs? but...don't quote me on that