Hi all
Just wondering if anyone else has had this happen or similar? I went up to the shed the other night and Holy cow :o
I have bubbled paint around the fuel filler? I am always very careful with fuel when filling, never wipe the paint work with anything other than clean polishing cloths.
I took off the filler cap and found that the paint has bubbled inside the fuel chamber and has slowly worked its way up to the outside duco, what to do? short of getting it re painted?
EGAS :'(
loss of adhesion can't be fixed except by removing the bad and replacing with new.
Sorry.
Is your cap seal leaking?
Quote from: ducpainter on April 08, 2009, 05:39:38 PM
loss of adhesion can't be fixed except by removing the bad and replacing with new.
Sorry.
Is your cap seal leaking?
Not sure, and would that be an issue seeing as it has started to bubble under the fuel cap in the area where the actual hole is in the tank?
EGAS
Quote from: EGAS1 on April 08, 2009, 06:25:42 PM
Not sure, and would that be an issue seeing as it has started to bubble under the fuel cap in the area where the actual hole is in the tank?
EGAS
Under normal conditions properly cured well adhered paint won't bubble from gas.
From your description it sounds like the cap was the catalyst. The issue is poor adhesion.
Quote from: ducpainter on April 08, 2009, 06:28:27 PM
Under normal conditions properly cured well adhered paint won't bubble from gas.
From your description it sounds like the cap was the catalyst. The issue is poor adhesion.
Thanks Ducpainter,
I was advised to pop this thread up on the main board as I did just post it on the OZ monster site initially. So I do appreciate your advice...........................so does this mean a total respray on the tank or can we get away with a part spray and blend?
EGAS
Quote from: EGAS1 on April 08, 2009, 06:32:34 PM
Thanks Ducpainter,
I was advised to pop this thread up on the main board as I did just post it on the OZ monster site initially. So I do appreciate your advice...........................so does this mean a total respray on the tank or can we get away with a part spray and blend?
EGAS
That would be up to your painter and what he finds for adhesion as he feathers the edges of the bubbling paint.
It also depends on the peeling. Is it peeling/bubbling to bare metal, or to the primer?
If it was peeling to metal I'd be inclined to sandblast the entire tank and start over. If it's peeling to primer I'd spend some time to see if it could be saved.
It's sometimes faster to just start over.
Hard to tell the extent of this without a picture but it sounds like the bubbled paint won't slow it down much. :) I think if it were my tank, I'd just carefully and lightly sand and clean up the bubbled area and seal it with some two-part epoxy primer, using a small artist brush or a Q-tip and then just ride the thing. Maybe consider re-painting it later or if I wanted to sell it.
had that happen to my bike. OE paint.
STILL waiting for my call-back about my warranty claim ;D
*bike is an early '05, bought new, so I'm sure you can do the math
happened on my 851 aluminum tank. lived with it for a while then had it repainted
by 'speedzone' in san diego.
[thumbsup]
Quote from: abby normal on April 10, 2009, 06:48:28 AM
happened on my 851 aluminum tank. lived with it for a while then had it repainted
by 'speedzone' in san diego.
[thumbsup]
yep, I eventually plan on getting my crap painted... sad, though, because the red/red has grown on me
mine did it to just repainted if you can find cheap labor i.e. a case of [drink] or two, i think paint cost me about 120 bucks for a two tone
My S4 is doing it too ,, 2nd respray its a common problem ,Gasohol is the culprit ,regular gas does not cause the problem.