hello,
i've been searching around and i don't see a lot of topics regarding triple tree and clip-on options for an S4. i saw the cyclecat trees but i haven't seen much else.
i'm a nooB so i'm not sure what size forks i have and what to look for. i have an '02 S4 Foggy with showa forks.
i'm looking for a combo where i don't have to raise the fork height and be able to use the stock grips and controls,etc.
please post a pic of your combo on your S4 and where you purchased them and prices would help a whole lot too.... ;D
thanks
You can use quite a variety of clip-ons, they just need to be 50mm diameter.
They'll have to go below the triple, though.
Your stock triple will foul most (if not all) clip-ons.
Here's some SpeedyMoto stuff:
https://secure.speedymoto.com/Merchant2/merchant.mvc?Screen=CTGY&Category_Code=MTC
Here's some Rizoma clipons, they fit on risers pretty much like the CycleCat stuff:
Rizoma at MotoWheels (http://www.motowheels.com/italian/myproducts.cfm?parentcategoryid=38%7CAluminum%20Billet&productID=3192&showDetail=1&categoryID=45%7CDucati%20Monster%20Billet&vendoridtodisplay=16%7CRIZOMA&filterFor=&collection=38%7CAluminum%20Billet)
You could go with Woodcraft.
Sorry, no really good pics. But there is this: http://www.ducati.ms/forums/showthread.php?t=2594&page=24
Third one down from the top.
Somehow I am unable to load pics.
Odd.
Quote from: Speeddog on May 28, 2008, 04:08:05 PM
You can use quite a variety of clip-ons, they just need to be 50mm diameter.
They'll have to go below the triple, though.
Your stock triple will foul most (if not all) clip-ons.
Here's some SpeedyMoto stuff:
https://secure.speedymoto.com/Merchant2/merchant.mvc?Screen=CTGY&Category_Code=MTC
Here's some Rizoma clipons, they fit on risers pretty much like the CycleCat stuff:
Rizoma at MotoWheels (http://www.motowheels.com/italian/myproducts.cfm?parentcategoryid=38%7CAluminum%20Billet&productID=3192&showDetail=1&categoryID=45%7CDucati%20Monster%20Billet&vendoridtodisplay=16%7CRIZOMA&filterFor=&collection=38%7CAluminum%20Billet)
thanks speeddog! which sets do you have on your S4? could you post a pic...please?
im waiting on some cash that will come in the next week and i'll be making an appt at flight cycles for penske's, triple and clip ons. this should be something that can be done in a couple of hours...no?
i think the cyclecat DBR adapters are meant to mimic the S4 triple setup. If you can find those then any 50mm clipons should fit above the tree.
i can't verify this though, since the CC site is down
I think the S4 shares the same triple as the S2R1000. You can get a number of clip-ons to fit. This picture is of a Vortex clip-on. It has no rise to it and is a very agressive riding position. I have installed a Cycle Cat DBR-13 on it now and it has about a 1.5" rise.
(https://farm4.static.flickr.com/3223/2535843182_81578bdfb0.jpg?v=0)
Notice this picture shows lowered gauges...
'01 and '02 S4 have the same triple and bars, I *think* they're the same as ST4 and ST4s.
S4R, S4Rt, and S4Rs have a 'conventional' triple, for tubular handlebars.
The CycleCat risers are indeed 50mm, so there's a bunch of clip-on options.
CycleCat is gone, but you can still buy the risers from oncycles.com:
http://www.oncycles.com/browse.asp?department=clearance&category=billetaccessories&subcategory=barriseradapters
Get 'em while you can, the price is a steal.
AFAIK, they're never going to make any more.
Here's a pic of my S4 with the CCat bars and adapters:
(http://farm3.static.flickr.com/2330/2535937989_0559ea2f23_o.jpg)
Quote from: spinned on May 29, 2008, 10:04:34 PM
I think the S4 shares the same triple as the S2R1000. You can get a number of clip-ons to fit. This picture is of a Vortex clip-on. It has no rise to it and is a very agressive riding position. I have installed a Cycle Cat DBR-13 on it now and it has about a 1.5" rise.
(https://farm4.static.flickr.com/3223/2535843182_81578bdfb0.jpg?v=0)
Notice this picture shows lowered gauges...
hey spinned, thanks for posting the pic. that looks a bit aggressive for me though. the CCat multi adjustable looks like it might work for me.
Quote from: Speeddog on May 30, 2008, 09:33:44 AM
'01 and '02 S4 have the same triple and bars, I *think* they're the same as ST4 and ST4s.
S4R, S4Rt, and S4Rs have a 'conventional' triple, for tubular handlebars.
The CycleCat risers are indeed 50mm, so there's a bunch of clip-on options.
CycleCat is gone, but you can still buy the risers from oncycles.com:
http://www.oncycles.com/browse.asp?department=clearance&category=billetaccessories&subcategory=barriseradapters
Get 'em while you can, the price is a steal.
AFAIK, they're never going to make any more.
hey speeddog,
thanks for the pic. i might want to keep my triple as you did, especially since i have the DP steering damper which covers up much of the triple anyway. have you seen the CCat multi-adjustable bars? are these what you have? looks like part #'s :
DBR23- Above Triple Clamp (w/S25+ DRA-1)= $395
DBR33- Above Triple Clamp (w/S15+ DRA-1)= $395
DRA1- Above Clamp Adapter Only= $155
i saw it on this website:
http://sportbiketrackgear2.homestead.com/cycle_cat_bars.html
(http://sportbiketrackgear2.homestead.com/BRFeatures4.jpg)
(http://sportbiketrackgear2.homestead.com/SBR3adj1DS.jpg)
I know this doesn't help much, but mine with cyclecat's triple and clip ons...
(http://applewood.smugmug.com/photos/280832322_XwKjm-L.jpg)
hydra,
Yes, I've got those CCat multi-adjustable bars.
I don't remember which ones I've got as far as the model#, but they're the shorter ones.
Quote from: Speeddog on May 30, 2008, 10:40:03 AM
hydra,
Yes, I've got those CCat multi-adjustable bars.
I don't remember which ones I've got as far as the model#, but they're the shorter ones.
cool...i hope there's still some available next when i get my cash. maybe you can help me order them? i'll give you a call early next week? i want to get some prices on some penske's as well.
Quote from: hydra on May 30, 2008, 10:52:26 AM
cool...i hope there's still some available next when i get my cash. maybe you can help me order them? i'll give you a call early next week? i want to get some prices on some penske's as well.
Yes, call me whenever you want. :)
Oncycles.com doesn't show any of the bars, I think your only chance is finding some used ones.
Hydra, I got a Cycle cat top triple, risers, and bars that I'm selling. They all are in titanium finish. I *think* the bar system is the dbr33, I'll have to check on that.
The CycleCat adapters ARE a steal @ $155 from Oncycles, but they don't specify if that's for the pair, or is they're sold individually...
-I would assume they're sold by the pair....Think I'm gonna pick some up while I still can!! [thumbsup]
Quote from: Johnster on May 30, 2008, 12:03:11 PM
The CycleCat adapters ARE a steal @ $155 from Oncycles, but they don't specify if that's for the pair, or is they're sold individually...
-I would assume they're sold by the pair....Think I'm gonna pick some up while I still can!! [thumbsup]
Especially since they're $58.05. ;)
Make sure you get a left and a right, they're not the same.
Quote from: pt33 on May 30, 2008, 11:30:27 AM
Hydra, I got a Cycle cat top triple, risers, and bars that I'm selling. They all are in titanium finish. I *think* the bar system is the dbr33, I'll have to check on that.
PM sent... :)
Top triple from an S4R, powdercoated, along with Woodcraft clip ons.
(http://i122.photobucket.com/albums/o264/AgentForty-7/s4%20part%20out/S4pics027.jpg)
Rizomas via PJ's Parts.
(http://www.smugmug.com/photos/305362333_77sEQ-L.jpg)
LSL with SpeedyMoto top triple
(http://i299.photobucket.com/albums/mm285/s2r1000/rizomashot.jpg?t=1212367437)
Quote from: Speeddog on May 30, 2008, 12:06:50 PM
Especially since they're $58.05. ;)
Make sure you get a left and a right, they're not the same.
oops......Where'd I get $155 from?!?!? [roll]
Ok so it is both for $58.05... DRA-02-03 means L and R.(the 02 + 03)....
thanks for the input and pics guys!
i knid of like the speedymoto with the LSL bars but it might be a trial and error thing to get it just right. i guess you don;t really know until you ride with the combination for a 100 mi or so...
Woodcraft goodnes
(http://img223.imageshack.us/img223/9980/vistadelpilotopr5.jpg)
(http://img504.imageshack.us/img504/9470/vistadelpiloto2uj2.jpg)
(http://img147.imageshack.us/img147/6238/desdeatrascj6.jpg)
So i realize this thread is super old, but I need to revisit the topic. I've got Apex clip-ons on the way, and i'm not sure if i'll be able to tolerate the super aggressive riding position or not. Do I have any cheap options here?
I've got this collecting dust if you'er interested...
(http://i4.photobucket.com/albums/y126/hundredpercentkill/dmf%20fs/photo-3.jpg)
what is that?.. I realize it's a triple of some kind but what are the two fork top looking things for?
Quote from: MAXdB on April 27, 2010, 05:43:13 PM
what is that?.. I realize it's a triple of some kind but what are the two fork top looking things for?
S4 style triple clamp w/ Cycle Cat (above triple) clip-on adaptors.
FYI: These should fit your S4RS also. [thumbsup]
Same as the previously posted pic:
Quote from: Speeddog on May 30, 2008, 09:33:44 AM
...
Here's a pic of my S4 with the CCat bars and adapters:
(http://farm3.static.flickr.com/2330/2535937989_0559ea2f23_o.jpg)
Quote from: DarkStaR on April 27, 2010, 05:11:54 PM
I've got this collecting dust if you'er interested...
(http://i4.photobucket.com/albums/y126/hundredpercentkill/dmf%20fs/photo-3.jpg)
you can always take a look at these triples. A M has them on his 99 m900. i'm going to get a pair. very good price compared to the speedymoto ones, and they can do custom boring if needed. they respond to emails within 12hrs. the gold finished ones are on sale. your butt and wallet will thank you
Quote from: Düb Lüv on April 27, 2010, 06:41:22 PM
you can always take a look at these triples. A M has them on his 99 m900. i'm going to get a pair. very good price compared to the speedymoto ones, and they can do custom boring if needed. they respond to emails within 12hrs. the gold finished ones are on sale. your butt and wallet will thank you
what "these" no links
http://www.imasrl.com/ENG/special-parts.asp (http://www.imasrl.com/ENG/special-parts.asp)
sorry about that. i'm a little doped up on meds.
BTW, being a U.S. citizen, you don't pay the VAT. the special boring is for the 42mm forks i have. so it's just an extra charge. the model 1 offset of their triples are 30mm. they can also special drill the top triple if you have an older bike and wanting new style bars or vise-versa.
on the price this is how they broke it down for me.
Kit mod.1 270 EUR
shipping cost 70 EUR
Special boring 40 EUR
payment trasfer cost (Paypal) 4%
--------------
Total 395,20 EUR x 1,34 = 529,56 USD
when i menstioned the gold finished triples being discounted, that was for the model 1s. since the model 1 and 2's are the same price it might include them too. 240 euro(discount)
pm sent to darkstar.
other than adapters, I guess i could try and track down a top triple, i'm tryna do this on a budget so maybe i'll wait for a used one to pop up.
"Handicapped parking" *lol* [thumbsup]
Quote from: scooby on May 30, 2008, 10:35:11 AM
(http://applewood.smugmug.com/photos/280832322_XwKjm-L.jpg)
did you wash your Bike? [cheeky]