Ducati Monster Forum

i have a m800. wondering if anyone has seen a set of pantah style belt covers that will fit/could be made to fit.

i seem to recal seeing someone with a set on here!?!

i have a bunch laying around

you mean the metal penis head type?

Like this?

Could you part with a set? 

Or 2 sets...lol..lol..."the penis head"...lol..lol... I want a set just on principle now!

BTW, they only fit the small cased motors (600,620,695,750 & 800)

yeah their the ones.
cheers, ill pm you

damn, that looks good.

A modified set on my S2R800

thanks.

still trying to figure out what to do with that spot that had the Pantah name plate.

How much?

honestly never knew anyone would want them

i have a bunch from the pantah engines i've built/blown.  all tossed into a box.


get a decal with "MONSTER" on it in the same style as the original PANTAH decal.  I thought about doing that.  but then again, i run with no covers at all.

out of interest will a pantah clutch cover fit i baby monster?

Nope.  The clutch slave on the Pantah clutch cover is actually on the right side...  Yours is on the left and uses a push-rod running through the transmission input shaft.

The old M600 and original M750 (pre1998???)  have the pantah style engine with the old style clutch slave and wet clutch.  there is no reason to swap it with a pantah though, UNLESS you wanted to upgrade to a dry clutch (which was a standard setup on the alazzurra and paso 750).  afaik, the crank shaft is the same size/spec and the engine case will take the pantah clutch cover no problem.

monster with right hand side clutch slave: (pantah style engine)
(http://www.motorcyclespecs.co.za/Gallery/Ducati%20Monster%20750%2096.jpg)


pantah dry clutch cover vented:
(http://bimotacagiva.guzzitech.com/Store/ventclutch3.JPG)

this mod will ONLY work on monsters that have a RIGHT HAND SIDE clutch slave as in the photo above

That's cool, I didn't know those fit the small case monsters.  Put me down as interested in a set too  ;)

covers on ebay:

http://cgi.ebay.com/ebaymotors/Cagiva-Alazzura-Belt-Covers-Ducati-Pantah-_W0QQcmdZViewItemQQhashZitem3f0a39b5b4QQitemZ270754493876QQptZMotorcyclesQ5fPartsQ5fAccessories (http://cgi.ebay.com/ebaymotors/Cagiva-Alazzura-Belt-Covers-Ducati-Pantah-_W0QQcmdZViewItemQQhashZitem3f0a39b5b4QQitemZ270754493876QQptZMotorcyclesQ5fPartsQ5fAccessories)

How owuld you go about upgrading to a dry clutch on one of these? I have a 97 M750, where would I find the parts for that?

How much money do you have sitting ready to spend?!?!?!

 [laugh] I had a feeling it would be pricey! I mentioned a dry clutch conversion to someone before and they said to just buy an M900 and avoid the hassle/cost involved.

pick up the side cover, the clutch parts and the cover and bob's your uncle.. either an alazzurra 650 or a paso 750

i'd put it at about 400-600 to find good pieces...

not necessarily.
i saw a fellow who basically angle cut the belt the cover (actually it was like an "S" curve, he did it with a scroll saw) and bolt the front half up, and the back half up, leaving an open "space" in between. it looked really slick. I will say however that i'm unsure if it was a larger case motor, or if he just routed out a slot and bolted them to a smaller motor anyway...

looked cool though.

this post is useless...

FML.

You're not crazy...

It was done by a friend of mine and that's how he got them to fit his 900...

yes! memory FTW.
got a pic of that? it looked really sick, i almost picked up a set of schlong-covers to do it myself.

Nope, no pic here, but he's still on the board (occassionally....) as 'm9hundo'.

Pantah style cover and Paso dry clutch:
(http://p1.bikepics.com/pics/2011%5C05%5C27%5Cbikepics-2214715-800.jpg)