Ducati Monster Forum

Moto Board => Tech => Topic started by: 09696802 on July 21, 2011, 12:03:14 PM

Title: installing new tripples and clamp-ons
Post by: 09696802 on July 21, 2011, 12:03:14 PM
So i was  lookin to put new tripples and clamp ons on my 696 and was wondering, not being 100% bike tech savy, is there any issues w/ alighnment like on a car when i take the old parts off amd install the new?
Title: Re: installing new tripples and clamp-ons
Post by: stopintime on July 21, 2011, 01:13:02 PM
As I understand it, there shouldn't be any such issues.
The lower triple hold the forks in their correct position.

Steering stem nut must be torqued correctly to put just the right amount of pressure on the two steering head bearings.

You should also find a way to mount the two clip ons at the same sweep angle.

Hopefully I'm not too far off here.
Get more than just my opinion [thumbsup]
Title: Re: installing new tripples and clamp-ons
Post by: DucNaked on July 22, 2011, 04:38:05 AM
On the 696 you shouldn't have to remove the steering stem nut for the top triple.  [thumbsup]
Title: Re: installing new tripples and clamp-ons
Post by: DucHead on July 22, 2011, 05:03:26 AM
Quote from: 09696802 on July 21, 2011, 12:03:14 PM
So i was  looking to put new tripples triples and clamp ons clip-ons on my 696 and I was wondering, not being 100% bike tech savy savvy, is are there any issues w/ alighnment alignment like on a car when i take the old parts off amd and install the new?

;D
Title: Re: installing new tripples and clamp-ons
Post by: 09696802 on July 22, 2011, 05:04:36 AM
Thanks for the info [thumbsup]
Title: Re: installing new tripples and clamp-ons
Post by: stopintime on July 22, 2011, 06:41:38 AM
Quote from: DucNaked on July 22, 2011, 04:38:05 AM
On the 696 you shouldn't have to remove the steering stem nut for the top triple.  [thumbsup]

Quote from: stopintime on July 21, 2011, 01:13:02 PM
...........
Get more than just my opinion [thumbsup]

Told you  [cheeky]


;D
Quote from: DucHead on July 22, 2011, 05:03:26 AM
;D

Boring day?  8)
Title: Re: installing new tripples and clamp-ons
Post by: DucNaked on July 22, 2011, 07:03:24 AM
One problem you will run into is that the headlight is attached to the stock triple. You'll have to come up with some sort of bracket or spacers to get it back to the correct height on an aftermarket triple. If you a search a couple of members have posted their solutions.
Title: Re: installing new tripples and clamp-ons
Post by: Slide Panda on July 22, 2011, 07:20:41 AM
Quote from: DucHead on July 22, 2011, 05:03:26 AM
;D

Oh yes - and be ready for the pedantic tendencies of folks here. I'm totally guilty of being one too
Title: Re: installing new tripples and clamp-ons
Post by: 09696802 on July 22, 2011, 12:28:56 PM
WOW! DickHead, hero memeber...... is also a hero spell checker. I didint realize I was writing for the english final, dont fail me [laugh]
Title: Re: installing new tripples and clamp-ons
Post by: DucHead on July 25, 2011, 02:38:37 PM
Quote from: 09696802 on July 22, 2011, 12:28:56 PM
WOW! DickHead, hero memeber...... is also a hero spell checker. I didint realize I was writing for the english final, dont fail me [laugh]

Looks like you're well on your way to a C-.

Good luck with the clip-ons.
Title: Re: installing new tripples and clamp-ons
Post by: 09696802 on July 26, 2011, 06:03:35 AM
 [laugh] thanks