powered by:
September 06, 2024, 12:19:33 AM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Please Help
Home
Help
Search
Login
Register
Discussion Boards
Introduce Yourself
FAQs and Policies
General Monster Forum
Remembering our friends...in Memorium
Riding Techniques
Tutorials
Tech
Accessories & Mods
Gear
Racing & Trackdays
Stolen Motorcycles
No Moto Content
Board Tech Issues
Local Club Boards
BOMb
RCP
Sponsors
Valley Desmo Service
California Cycleworks
MotorcycleGear.Com
Monsterparts
Minor Sponsor Board
Sponsor Info
Flea Market
Monsters for Sale
Monsters Wanted
Other Bikes
Parts for Sale
Parts Wanted
Gear for Sale
Misc for Sale/Wanted
Ducati Monster Forum
>
Moto Board
>
Tech
(Moderator:
Speeddog
) >
Will the metal cutting disc on a Dremel actually cut through metal?
Pages:
1
2
[
3
]
Go Down
« previous
next »
Print
Author
Topic: Will the metal cutting disc on a Dremel actually cut through metal? (Read 10970 times)
rat_fink
New Member
Offline
Posts: 10
Re: Will the metal cutting disc on a Dremel actually cut through metal?
«
Reply #30 on:
July 16, 2008, 04:07:17 PM »
Yeah it will but, don't git to aggresive. Why?, you can set the dremel on fire, been there, done that. Bought a roto zip, by boush, model rz2, all the dremel stuff will fit it. Sweet tool, git as aggresive as you want, no fire, fire bad
Logged
Popeye the Sailor
For $50 you can touch my
Post Whore
Offline
Posts: 16479
Re: Will the metal cutting disc on a Dremel actually cut through metal?
«
Reply #31 on:
July 16, 2008, 09:54:26 PM »
Quote from: rat_fink on July 16, 2008, 04:07:17 PM
Yeah it will but, don't git to aggresive. Why?, you can set the dremel on fire, been there, done that. Bought a roto zip, by boush, model rz2, all the dremel stuff will fit it. Sweet tool, git as aggresive as you want, no fire, fire bad
You can set anything on fire.
Logged
If the state had not cut funding for the mental institutions, this project could never have happened.
tangueroHondo
Full Member
Offline
Posts: 196
Re: Will the metal cutting disc on a Dremel actually cut through metal?
«
Reply #32 on:
July 17, 2008, 09:24:01 AM »
Quote from: rat_fink on July 16, 2008, 04:07:17 PM
Yeah it will but, don't git to aggresive. Why?, you can set the dremel on fire, been there, done that. Bought a roto zip, by boush, model rz2, all the dremel stuff will fit it. Sweet tool, git as aggresive as you want, no fire, fire bad
Hey - got on the dremel site to check out the Bosch RZ2 compatability and look what ist says at the bottom of the web page:
Copyright © 2008, Robert Bosch Tool Corporation. All Rights Reserved.
I did not know that.
Logged
darkduke
Full Member
Offline
Posts: 101
'07 S4rs
Re: Will the metal cutting disc on a Dremel actually cut through metal?
«
Reply #33 on:
July 18, 2008, 05:22:53 AM »
Quote from: aaronb on July 14, 2008, 04:13:09 PM
cutting a few tabs off should not require a 4.5" angle grinder. really not a big deal. you should be able to get them off with 1 or 2 of the larger fiber reinforced disks. just wind the dremel up to ten and cut slow, be careful to keep the blade straight once into the bracket, touching the sides will ruin the disk very quickly. best bet is to draw a line with the disk right at the weld then work the disk back and forth over the line until you're through. once the tabs are off you can clean them up with a sanding drum or cylindrical stone. just take your time and it should be no problem. 5-15 minutes per tab depending on how clean you take the welds down to.
use these, #456 1-1/2"fiber glass reinforced cut-off disk
http://www.dremel.com/en-us/AttachmentsAndAccessories/Pages/AttachmentsDetail.aspx?pid=456
and don't forget safety glasses, if (when) the disk comes apart fragments fly everywhere.
+1 on everything aaronb said here, I used a dremel on a few different pieces (including stainless steel pieces on the exhaust). Just get the fiber discs and don't push too hard (have some patience) and they last longer than you would think.
Logged
-ZG Windscreen - Pazzo Levers - CRG Lanesplitters - Arrow Steering Damper - Retro Tank Logos - Tail Chop - Speedymoto Clutch Cover, Springs, Caps, DP Carbon Rear Hugger, DP ECU & Open Airbox with Chopped Titanium Arrows
Pages:
1
2
[
3
]
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Introductions
-----------------------------
=> Introduce Yourself
=> FAQs and Board Policies
-----------------------------
Moto Board
-----------------------------
=> General Monster Forum
=> In Memorium...Remembering our Friends
=> Riding Techniques
=> Tutorials
=> Tech
=> Accessories & Mods
=> Gear
=> Racing & Trackdays
=> Stolen Motorcycles
=> Random Cool Pics
-----------------------------
Kitchen Sink
-----------------------------
=> No Moto Content
===> Board Suggestions
===> Fixed Board Issues
=> Stella's Pop
-----------------------------
DMF Sponsors
-----------------------------
=> Valley Desmo Service
=> Ca-Cycleworks
=> New Enough.Com
=> Monsterparts
=> Minor Sponsors
=> Misc Info
-----------------------------
Local Clubs
-----------------------------
=> Monster Women
=> Ducati MOB
=> SoCal Monsters
=> CAM
=> OZ monsters
=> NorthWest
=> NEMHA
=> NYMMC
=> MHM
=> SoCO DOG
=> DFWM
=> MADDOG
=> MOCHA
=> THCM
=> AZDRA
=> M-ROC
=> Central Cal Monsters
=> DOCSF
=> MCMC
=> DDCM
=> DOCTOR
=> Hoosier Hooligans
=> OMHA
=> DOCIA
=> Rising Sun Ducatis
=> MCM
=> NMMR
=> MIA
=> Desmotropic
=> COW
=> MOTH
=> DesmOK
=> Bayou Country Ducati Riders
=> DeVal Mostro
=> Coastal Ducati Club
-----------------------------
Configurators and Calculators
-----------------------------
=> Valve Shim Calculator
Loading...
SimplePortal 2.1.1