powered by:
September 29, 2024, 10:16:06 PM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Please Help
Home
Help
Search
Login
Register
Discussion Boards
Introduce Yourself
FAQs and Policies
General Monster Forum
Remembering our friends...in Memorium
Riding Techniques
Tutorials
Tech
Accessories & Mods
Gear
Racing & Trackdays
Stolen Motorcycles
No Moto Content
Board Tech Issues
Local Club Boards
BOMb
RCP
Sponsors
Valley Desmo Service
California Cycleworks
MotorcycleGear.Com
Monsterparts
Minor Sponsor Board
Sponsor Info
Flea Market
Monsters for Sale
Monsters Wanted
Other Bikes
Parts for Sale
Parts Wanted
Gear for Sale
Misc for Sale/Wanted
Ducati Monster Forum
>
Kitchen Sink
>
No Moto Content
(Moderators:
ducpainter
,
Statler
) >
Diagnosing a reluctant air compressor
Pages: [
1
]
2
Go Down
« previous
next »
Print
Author
Topic: Diagnosing a reluctant air compressor (Read 1939 times)
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Diagnosing a reluctant air compressor
«
on:
August 02, 2015, 08:52:09 AM »
I scored an older Campbell Hausfield 20 gallon compressor at an auction for $40 and was pretty happy about that.
It works, sort of.
From empty it will charge to 90psi and shut off. When pressure drops below the cut off is the problem.
The motor will either not turn and hum (trips the breaker if it goes long enough) or it does turn, but slow (struggling)
I'm almost certain the unloader valve works correctly. When it hits cut off pressure the motor stops and a little finger actuates the small valve at the end of the unloader line which vents pressure over the piston to atmosphere.
Both the start and run capacitors on the motor "look" OK but I haven't actually tested anything.
When the motor will not start and just sits there humming, if I kill power and rotate things with my fingers on the drive belt, even just a little, the motor will run but slow as mentioned above.
Any ideas?
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
the_Journeyman
Hero Member
Offline
Posts: 9181
Molly & Syreena, the Italian mistresses
Re: Diagnosing a reluctant air compressor
«
Reply #1 on:
August 02, 2015, 08:58:30 AM »
From a very basic view, it sounds like something is binding in the motor/piston driveline. Something is causing enough resistance to draw enough power to trip the breaker. It could be anything from the electric motor winding coming undone to something bent somewhere between there and the piston.
JM
Logged
Got Torque?
Quote from: r_ciao on January 28, 2011, 10:30:29 AM
ADULT TRUTHS
10. Bad decisions make good stories.
Speeddog
West Valley Flatlander
Flounder-Administrator
Post Whore
Offline
Posts: 14813
RIP Nicky
Re: Diagnosing a reluctant air compressor
«
Reply #2 on:
August 02, 2015, 09:00:55 AM »
There's a check valve between the compressor output and the tank, usually mounted directly to the tank.
Likely that's leaking, backfilling the cylinder, and the motor cant get past that load from a dead stop.
Logged
- - - - - Valley Desmo Service - - - - -
Reseda, CA
(951) 640-8908
~~~ "We've rearranged the deck chairs, refilled the champagne glasses, and the band sounds great. This is fine." - Alberto Puig ~~~
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78670
DILLIGAF
Re: Diagnosing a reluctant air compressor
«
Reply #3 on:
August 02, 2015, 09:02:15 AM »
I think Nick nailed it.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #4 on:
August 02, 2015, 09:18:03 AM »
Quote from: Speeddog on August 02, 2015, 09:00:55 AM
There's a check valve between the compressor output and the tank, usually mounted directly to the tank.
Likely that's leaking, backfilling the cylinder, and the motor cant get past that load from a dead stop.
If that were the case, pressure should vent from the unloader line when I actuate the relief valve with a screwdriver, but that line doesn't recharge over time.
When the motor won't turn under power it takes relatively little effort to roll things over by moving the belt.
Should I still look at the check valve?
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
Speeddog
West Valley Flatlander
Flounder-Administrator
Post Whore
Offline
Posts: 14813
RIP Nicky
Re: Diagnosing a reluctant air compressor
«
Reply #5 on:
August 02, 2015, 09:32:55 AM »
Quote from: Monsterlover on August 02, 2015, 09:18:03 AM
If that were the case, pressure should vent from the unloader line when I actuate the relief valve with a screwdriver, but that line doesn't recharge over time.
When the motor won't turn under power it takes relatively little effort to roll things over by moving the belt.
Should I still look at the check valve?
Well, that complicates things.
Does the motor turn even a little bit when it restarts?
Will it start turning if you hold the unloader valve open and power it back up??
Logged
- - - - - Valley Desmo Service - - - - -
Reseda, CA
(951) 640-8908
~~~ "We've rearranged the deck chairs, refilled the champagne glasses, and the band sounds great. This is fine." - Alberto Puig ~~~
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #6 on:
August 02, 2015, 09:42:28 AM »
Quote from: Speeddog on August 02, 2015, 09:32:55 AM
Well, that complicates things.
Does the motor turn even a little bit when it restarts?
Will it start turning if you hold the unloader valve open and power it back up??
No and no.
It just hums. If I roll the belt a bit it will turn under power but barely a rev and its slow and struggling.
As a test I just emptied the tank and it still just hums with no turn.
Then, rolling the belt a couple inches... motor struggles for just an instant then runs normal rpm and the tank is charging as it should.
Also, and thisay be new, I'm hearing a scraping sound that sounds cyclic in its timing but it doesn't match motor or compressor rpm.
Could be unrelated bearing noise maybe.
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78670
DILLIGAF
Re: Diagnosing a reluctant air compressor
«
Reply #7 on:
August 02, 2015, 09:44:34 AM »
Check the start windings.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #8 on:
August 02, 2015, 10:16:32 AM »
Quote from: ducpainter on August 02, 2015, 09:44:34 AM
Check the start windings.
Capacitor?
Or actual windings in the motor? Motor functionality is not something I know well.
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78670
DILLIGAF
Re: Diagnosing a reluctant air compressor
«
Reply #9 on:
August 02, 2015, 11:58:56 AM »
Yeah...the capacitor.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
Popeye the Sailor
For $50 you can touch my
Post Whore
Offline
Posts: 16493
Re: Diagnosing a reluctant air compressor
«
Reply #10 on:
August 02, 2015, 12:10:07 PM »
You'll recognize it Kevin-it's full of flux.
Logged
If the state had not cut funding for the mental institutions, this project could never have happened.
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #11 on:
August 02, 2015, 02:22:43 PM »
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #12 on:
August 02, 2015, 02:23:09 PM »
Would the start capacitor be the larger one?
There are two
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
sno_duc
Hero Member
Offline
Posts: 811
Re: Diagnosing a reluctant air compressor
«
Reply #13 on:
August 03, 2015, 06:28:20 PM »
Check the centrifugal switch, the start winding, and the start capacitor.
Something is lacking in the start circuit.
http://www.capacitorguide.com/motor-starting-capacitor/
Logged
A conclusion is the place you got tired of thinking
Monsterlover
The best kind of whore is a
Post Whore
Offline
Posts: 18336
I will save Skynet from Sarah Connor
Re: Diagnosing a reluctant air compressor
«
Reply #14 on:
August 04, 2015, 02:20:14 AM »
Logged
"The Vincent was like a bullet that went straight; the Ducati is like the magic bullet in Dallas that went sideways and hit JFK and the Governor of Texas at the same time."--HST **"A man who works with his hands is a laborer. A man who works with his hands and his brain is a craftsman. A man who works with his hands, brains, and heart is an artist." -Louis Nizer**
Pages: [
1
]
2
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Introductions
-----------------------------
=> Introduce Yourself
=> FAQs and Board Policies
-----------------------------
Moto Board
-----------------------------
=> General Monster Forum
=> In Memorium...Remembering our Friends
=> Riding Techniques
=> Tutorials
=> Tech
=> Accessories & Mods
=> Gear
=> Racing & Trackdays
=> Stolen Motorcycles
=> Random Cool Pics
-----------------------------
Kitchen Sink
-----------------------------
=> No Moto Content
===> Board Suggestions
===> Fixed Board Issues
=> Stella's Pop
-----------------------------
DMF Sponsors
-----------------------------
=> Valley Desmo Service
=> Ca-Cycleworks
=> New Enough.Com
=> Monsterparts
=> Minor Sponsors
=> Misc Info
-----------------------------
Local Clubs
-----------------------------
=> Monster Women
=> Ducati MOB
=> SoCal Monsters
=> CAM
=> OZ monsters
=> NorthWest
=> NEMHA
=> NYMMC
=> MHM
=> SoCO DOG
=> DFWM
=> MADDOG
=> MOCHA
=> THCM
=> AZDRA
=> M-ROC
=> Central Cal Monsters
=> DOCSF
=> MCMC
=> DDCM
=> DOCTOR
=> Hoosier Hooligans
=> OMHA
=> DOCIA
=> Rising Sun Ducatis
=> MCM
=> NMMR
=> MIA
=> Desmotropic
=> COW
=> MOTH
=> DesmOK
=> Bayou Country Ducati Riders
=> DeVal Mostro
=> Coastal Ducati Club
-----------------------------
Configurators and Calculators
-----------------------------
=> Valve Shim Calculator
Loading...
SimplePortal 2.1.1