powered by:
September 01, 2024, 02:58:10 AM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Please Help
Home
Help
Search
Login
Register
Discussion Boards
Introduce Yourself
FAQs and Policies
General Monster Forum
Remembering our friends...in Memorium
Riding Techniques
Tutorials
Tech
Accessories & Mods
Gear
Racing & Trackdays
Stolen Motorcycles
No Moto Content
Board Tech Issues
Local Club Boards
BOMb
RCP
Sponsors
Valley Desmo Service
California Cycleworks
MotorcycleGear.Com
Monsterparts
Minor Sponsor Board
Sponsor Info
Flea Market
Monsters for Sale
Monsters Wanted
Other Bikes
Parts for Sale
Parts Wanted
Gear for Sale
Misc for Sale/Wanted
Ducati Monster Forum
>
Moto Board
>
Tech
(Moderator:
Speeddog
) >
Carb Re-jetting
Pages: [
1
]
Go Down
« previous
next »
Print
Author
Topic: Carb Re-jetting (Read 1230 times)
dp351
New Member
Offline
Posts: 3
Carb Re-jetting
«
on:
February 13, 2024, 08:46:09 AM »
The results from installing a Factory Pro jet kit in my 1996 M900 are exactly what I was hoping for. New main and pilot jets, needles and emulsion tubes. The transition from the idle circuit to the needle jet is smooth as butter now. Still need to iron out a slightly rough off idle situation but the bike is much more rideable in stop and go traffic.
However, I took the bike into the canyon twisties and after a while, I started getting a lean condition. The roads I was on were very tight corners with lots of back and forth and mostly 2nd gear, winding it up until the next corner. As I was going down the mountain on decel I started to get some popping and eventually loss of power. I pulled over to see if my fuel line popped off (it's happened a couple of times on this bike) but all was fine.
My thoughts are that my float levels need to be adjusted and that I was sucking all the fuel out of the bowls quicker than it could fill back up. On the highways and around town it's doing great, but extended high RPMs at 3/4 throttle to WFO, is it draining the bowls?
What are your thoughts?
Logged
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78609
DILLIGAF
Re: Carb Re-jetting
«
Reply #1 on:
February 13, 2024, 09:40:09 AM »
Two things I'd check.
First I'd check to be sure the fuel pump is pumping. There are options if yours isn't.
If it is pumping, check your float levels. IIRC they should be at 14mm. The directions for the jet kit should have a spec.
If those two guesses don't solve the issue, there's a small filter at the fuel inlet to the carbs that could possibly be clogged.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #2 on:
February 13, 2024, 11:33:04 AM »
÷1.
Yes float is 14mm.
Then add to your checklist to methodically go through:
Does your bike have a manual or vacuum fuel tap? If it's vacuum, then replace with a 5/16 minimum bore manual fuel tap.
What do the spark plug colours say after the ride? That informs the next point.
What jetting option you settle with from the kit?
Standard airbox?
Check for inlet manifold leaks too.
Logged
2015 Scrambler 800
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #3 on:
February 13, 2024, 02:27:21 PM »
Oh forgot to ask, V or W heads?
Logged
2015 Scrambler 800
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78609
DILLIGAF
Re: Carb Re-jetting
«
Reply #4 on:
February 13, 2024, 02:48:20 PM »
My 96 M900 has V heads. I think they all did...probly wrong.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #5 on:
February 13, 2024, 04:35:19 PM »
I think the Ws started appearing late 96, but it could have been 97. Glad you got the good ones
Logged
2015 Scrambler 800
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #6 on:
February 13, 2024, 04:37:52 PM »
I actually like the Factory Pro needle and spring better than the DJ ones. I just think FP are a little conservative with their main jets.
Logged
2015 Scrambler 800
Frank C
Jr. Member
Offline
Posts: 54
Re: Carb Re-jetting
«
Reply #7 on:
March 24, 2024, 04:54:31 AM »
Sorry for the late reply for an older thread...but just to clarify...according to Ducati the W heads were for the 97 model year. But the W heads on my 97 were stamped 96. So you are both right.
As for the issue...why ask V vs W? Just curious.
Sounds like the diaphragm in the fuel pump is failing. Should check and see if the oil level is suddenly increasing. Ask me how I know
With a failing pump, the fuel is now gravity fed. And with the tank outlet at the back of the tank, going down hill with a partially tank of fuel could starve the carbs.
Logged
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #8 on:
March 24, 2024, 07:19:10 AM »
V and W heads have different jetting requirements and the jet kits are different. That's reflected in the DJ catalogue.
Gravity feed allows about half a tank use before fuel starvation as the carb inlet is higher than the tank. Suspect a fuel pump failure without a blockage under those conditions, but suspect a blockage if fuel starvation occurs with a full tank. It can occur in a few places, tank outlet, tap, hose collapse, pump, carb inlet mesh, float valve, blocked jets. A blocked tank breather strangles fuel too which can be crud or a pinched hose, stressing fuel pumps in general.
Logged
2015 Scrambler 800
Frank C
Jr. Member
Offline
Posts: 54
Re: Carb Re-jetting
«
Reply #9 on:
March 25, 2024, 04:07:49 AM »
Didn't realize. Makes sense, especially since the cams are also different. Its been so long, I forgot which kit I used. Couldn't stand the needle jets becoming ovals. So I solved the problem by going with V heads with IE cams and flat slides
As always, thank you for your insight.
Logged
koko64
Post Whore
Offline
Posts: 15681
Re: Carb Re-jetting
«
Reply #10 on:
March 25, 2024, 10:40:57 AM »
Nice motor recipe. High comp pistons would complete that nicely (with heavy duty engine studs, altered ignition timing and higher octane fuel).
Logged
2015 Scrambler 800
Frank C
Jr. Member
Offline
Posts: 54
Re: Carb Re-jetting
«
Reply #11 on:
March 27, 2024, 05:51:40 PM »
Funny...that was the last thing left to do on the monster.
Focused on everything else first...suspension, wheels, brakes, lighting, ignition, exhaust, and lightweight rotating stuff on the engine.
Then I picked up an ST4s just a mile down the road and never got around to the big bore kit.
Son turns 16 next year. Might just wait for him to blow it up first before putting new pistons and bores in. Same reason why I have a big block sitting in the basement for the old F-150
Logged
Pages: [
1
]
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Introductions
-----------------------------
=> Introduce Yourself
=> FAQs and Board Policies
-----------------------------
Moto Board
-----------------------------
=> General Monster Forum
=> In Memorium...Remembering our Friends
=> Riding Techniques
=> Tutorials
=> Tech
=> Accessories & Mods
=> Gear
=> Racing & Trackdays
=> Stolen Motorcycles
=> Random Cool Pics
-----------------------------
Kitchen Sink
-----------------------------
=> No Moto Content
===> Board Suggestions
===> Fixed Board Issues
=> Stella's Pop
-----------------------------
DMF Sponsors
-----------------------------
=> Valley Desmo Service
=> Ca-Cycleworks
=> New Enough.Com
=> Monsterparts
=> Minor Sponsors
=> Misc Info
-----------------------------
Local Clubs
-----------------------------
=> Monster Women
=> Ducati MOB
=> SoCal Monsters
=> CAM
=> OZ monsters
=> NorthWest
=> NEMHA
=> NYMMC
=> MHM
=> SoCO DOG
=> DFWM
=> MADDOG
=> MOCHA
=> THCM
=> AZDRA
=> M-ROC
=> Central Cal Monsters
=> DOCSF
=> MCMC
=> DDCM
=> DOCTOR
=> Hoosier Hooligans
=> OMHA
=> DOCIA
=> Rising Sun Ducatis
=> MCM
=> NMMR
=> MIA
=> Desmotropic
=> COW
=> MOTH
=> DesmOK
=> Bayou Country Ducati Riders
=> DeVal Mostro
=> Coastal Ducati Club
-----------------------------
Configurators and Calculators
-----------------------------
=> Valve Shim Calculator
Loading...
SimplePortal 2.1.1