I checked all the normal sources and came up with nothing.
I will pay someone $5.00 if they can help me find the bolts listed below. For real.
My High pipes require the use of spacers which are about 16mm thick the spacers space out foot peg brackets. This takes away from the amount of bolt being threaded into the engine cases/frame mounts.
One of the bolts even pulled out when the bike was knocked over last year.
Here is what I need:
8mm x 1.25
shoulder diameter 12mm
Shoulder Length 20mm
Threaded Length: 30 or 35mm
Head Diameter: 24mm could use a smaller one in combination with a washer if I have to
10mm x 1.5
shoulder diameter 12mm
Shoulder Length 20mm
Threaded Length: 40mm
Head Diameter: 24mm could use a smaller one in combination with a washer if I have to
Bolt depot?
http://www.boltdepot.com/dimension.aspx?cc=68&cs=245&cm=23 (http://www.boltdepot.com/dimension.aspx?cc=68&cs=245&cm=23)
http://www.rinomechanical.com/stainless-metric-shoulder-screws.htm (http://www.rinomechanical.com/stainless-metric-shoulder-screws.htm)
Quote from: yuu on May 18, 2009, 07:39:47 PM
Bolt depot?
http://www.boltdepot.com/dimension.aspx?cc=68&cs=245&cm=23 (http://www.boltdepot.com/dimension.aspx?cc=68&cs=245&cm=23)
Thread length is too short at only 16mm :(
Quote from: ducpainter on May 18, 2009, 07:58:09 PM
http://www.rinomechanical.com/stainless-metric-shoulder-screws.htm (http://www.rinomechanical.com/stainless-metric-shoulder-screws.htm)
It would appear that the contest is over. Provided these folks don't attempt to charge me hundreds of dollars. we'll find out tomorrow
Congrats to Ducpainter!
http://www.mcmaster.com/# (http://www.mcmaster.com/#) also has just about everything
Quote from: Paegelow on May 18, 2009, 08:30:24 PM
http://www.mcmaster.com/# (http://www.mcmaster.com/#) also has just about everything
Yeah I love that place but they were no help on these
Quote from: gage on May 18, 2009, 08:21:31 PM
It would appear that the contest is over. Provided these folks don't attempt to charge me hundreds of dollars. we'll find out tomorrow
Congrats to Ducpainter!
Who says there's no free lunch. ;D
$750!!!! :o
Ok so that ain't gonna work.
New plan:
Long Hex head bolt: 10mm x 1.5
Metal Sleeve: OD 12mm ID 10mm Length 20
24 mm OD fender washer
Think that will work?
Quote from: gage on May 18, 2009, 08:21:31 PM
It would appear that the contest is over. Provided these folks don't attempt to charge me hundreds of dollars. we'll find out tomorrow
Congrats to Ducpainter!
You didn't say anything about them being affordable, just that someone had to find them. You owe DP 5 bucks. ;D
i think i may be able to get you some, there is a company here call fastenal that specialize in fasteners. I can ask for you if you like. just PM me the exact specs.
Quote from: DDDDan on May 19, 2009, 03:40:25 PM
You didn't say anything about them being affordable, just that someone had to find them. You owe DP 5 bucks. ;D
He told me to bring more Jerky to DIMBY
Quote from: He Man on May 19, 2009, 04:28:45 PM
i think i may be able to get you some, there is a company here call fastenal that specialize in fasteners. I can ask for you if you like. just PM me the exact specs.
That's a very generous offer!
I did check the fastenal website before posting this and unfortunately didn't have any luck.
It would seem that a threaded portion of a should bolt makes up only 20% of that bolts overall length.
Yea some of the stuff arent listed on their website, you have to go to their store (its 2 blocks from my house....i live in an industrial park)
Quote from: He Man on May 19, 2009, 07:07:09 PM
Yea some of the stuff arent listed on their website, you have to go to their store (its 2 blocks from my house....i live in an industrial park)
The specs are listed in the OP. I would prefer either stainless or hardened.
THanks Again and Good Luck!
Quote from: gage on May 19, 2009, 07:25:45 AM
$750!!!! :o
Ok so that ain't gonna work.
New plan:
Long Hex head bolt: 10mm x 1.5
Metal Sleeve: OD 12mm ID 10mm Length 20
24 mm OD fender washer
Think that will work?
Wow, never knew a few bolts could be so expensive.
Think outside the box. They are available, and for a lot less money than that. If you give up PM me :)
I can check with my local shop called King Bolt but I can't get out there until the last weekend of May. :P The sleeve idea should work perfectly fine.
http://www.tastynuts.com/site/frames/frameset_shoponline.htm (http://www.tastynuts.com/site/frames/frameset_shoponline.htm)
on the left side of the screen, go to "DUCATI - SPECIAL OFFERS"
keep in mind that the lengths listed are the total length of the bolts (shoulder and thread) but know that the shoulder is the exact size you need.
McMaster is a good place to start. Chance are there is one in you neighborhood or at least not too far away.
I'm probably misinterpreting something, but why can't you just use longer regular bolts with your existing spacers? The shoulder bolts are probably the cleanest solution but it sounds like you may have to get them machined to get the exact ones you want.
Edit, Doh, after reading more, I see that sleeves or spacers are already under consideration. Amazing how the simplest change from stock always seems to bring unexpected consequences.
http://www.tpoparts.com/catalog/product_info.php?products_id=86&osCsid=f64b3ce5a93e88f054a182c95282a136 (http://www.tpoparts.com/catalog/product_info.php?products_id=86&osCsid=f64b3ce5a93e88f054a182c95282a136)
(http://www.tpoparts.com/catalog/product_thumb.php?img=images/Monster_Shoulder_Bolt.jpg&w=320&h=236)