$20 Cycle Cat Front Stands on clearance............

[MrFryMoto]

wish i didn't already have a front stand 

however - i could use a new rear-stand that uses spools (as opposed to the 'L' shaped under-swingarm holders)

[Pedro-bot]

I need some help, here, and this might be a thread jack, but this is a sweet deal.  2 things..
1.    I believe I have to get front fork sliders/pegs in order to use the front stand...
2.    I would like to buy something else too, but not sure of fitment
https://www.oncycles.com/browse.asp?page=3&department=clearance&category=billetaccessories
which one will fit a S4RS...

thanks for the help..
i would like to score a triple clamp if possible

1. No, you don't need the fork sliders to use this front stand. The rubber mounts of the front stand cradle the bottom of the forks thereby lifting the front wheel off the ground.

2. I don't think the top triples are available for your bike.

[pennyrobber]

I was holding out to get a PitBull front stand with the bottom triple pin but couldn't pass this up. Thanks for the heads up.

[AfroStar]

Thanks Pedro,

yeah, they didn't have the DTC-7 for my bike.  I did get the front stand and the billet 3 piece clutch cover $50 bucks..not too bad.. I'm a sucker for deals, and not just buying one thing... 

oh well, Just in case I want to change it up..

[fastwin]

Nice deal for sure! You shouldn't need anything else to use the stand. The set up looks very similar to my Pit Bull front stand. And for those who have never used a front stand like this YOU HAVE TO HAVE THE BIKE SUPPORTED BY A REAR STAND FIRST!!!! Rear stand first THEN the front stand!!

[DucHead]

I was holding out to get a PitBull front stand with the bottom triple pin but couldn't pass this up. Thanks for the heads up.

I have a PitBull front stand with a pin, but I ordered the Cycle Cat stand anyway.  If you're just removing the front wheel, the Cycle Cat stand will make the job a tad easier, as the legs of the PitBull stand are a little in the way of the axle.

[DrDesmo]

I have a PitBull front stand with a pin, but I ordered the Cycle Cat stand anyway.  If you're just removing the front wheel, the Cycle Cat stand will make the job a tad easier, as the legs of the PitBull stand are a little in the way of the axle.

Plus the handle removes for storage or whatever 

Adam

[somegirl]

Just ordered 2.    Our shipping charges were a bit more than NAKID's but still a good deal.

[Popeye the Sailor]

Just ordered 2.    Our shipping charges were a bit more than NAKID's but still a good deal.

I better get a second bike to put on the other one then. 

[minnesotamonster]

I caved and bought one 

[NAKID]

I got a notification that it will be delivered TOMORROW! Holy crap, I only paid for the UPS Ground. There may be an issue though, it was shipped signature required. The wife is out of town so I may not be there when they deliver...

[Desmo Demon]

I didn't need them, but I think it is an upgrade from what I've been using, so.....I just now called them up and ordered three of them. They are out of the red ones, but they still have silver in stock.....I kept teetering between buying 3 or 4 and settled on the lesser. I figure I can sell my old two stands and make up some of the cost of these three, plus, if I decide to sell one of these new ones, I have a few friends who could use them......Hmmmm...Maybe I should order a fourth. LOL

[DrDesmo]

annnnd I just ordered a third one, hey what the hell 

Adam

[Pedro-bot]

For those that wanted the red one, you can always have it powder coated. 


Of course that would cost more $$, but if you really wanted to.....what the hell. 

[DrDesmo]

For those that wanted the red one, you can always have it powder coated. 


Of course that would cost more $$, but if you really wanted to.....what the hell. 

Or, wrap it in red nylon or gaffers tape 

Adam