Main Menu

Seat size?

Started by NakedNFast, November 19, 2009, 01:56:56 PM

Previous topic - Next topic
Print
Go Down Pages1
User actions

NakedNFast

November 19, 2009, 01:56:56 PM
Unfortunately I am not the proud owner of a Ducati Monster :( but imitation is the greatest form of flattery! I am building a custom motor cycle and would love to put the Ducati monster seat on it. Will someone please measure under the front part of the seat that comes in contact with the tank for me? I just need the narrow dimension and the wide dimension. Thank you for your time! [bow_down]

-NakedNFast

NakedNFast

#1
November 19, 2009, 02:28:20 PM
cmon guys jus mozy out to the garage and take two quick measurements! please!

Speeddog

#2
November 19, 2009, 04:32:01 PM
Not real clear on which parts of the seat you want measured.....
- - - - - Valley Desmo Service - - - - -
Reseda, CA
(951) 640-8908

~~~ "We've rearranged the deck chairs, refilled the champagne glasses, and the band sounds great. This is fine." - Alberto Puig ~~~

Ducatl

#3
November 19, 2009, 04:40:47 PM
Also, FYI the monster seat isn't of particularly amazing or useful construction, it's kind of shitty IMO. That said I doubt it will really work with anything but a monster tank and at any other angle than factory, did I mention the base is just plastic with tabs and a complicated latching mechanism?

NakedNFast

#4
November 19, 2009, 07:09:01 PM
Im welding my own sub fram to acomedate for the seat so the plastic will be fine I am a manucfacturing engineer with plenty of machining and design experience so I am sure I will be able to figure something out to get that sucker to mount up on my bike. Im sorry if its not clear what I need measured so I made this little picture to show ya! I need the widths of the under side of the seat not the top where u sit. THANKS!

ducpainter

#5
November 22, 2009, 05:56:38 AM
Quote from: NakedNFast on November 19, 2009, 07:09:01 PM
Im welding my own sub fram to acomedate for the seat so the plastic will be fine I am a manucfacturing engineer with plenty of machining and design experience so I am sure I will be able to figure something out to get that sucker to mount up on my bike. Im sorry if its not clear what I need measured so I made this little picture to show ya! I need the widths of the under side of the seat not the top where u sit. THANKS!


FYI...

the seats changed in the year 2000.

I can measure an earlier seat, but I'm not positive it will be the same as a later model seat.

Which do you plan on using?
"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent."


mendoje

#6
November 22, 2009, 08:24:00 AM Last Edit: November 22, 2009, 08:27:00 AM by mendoje
I think the seats changed in some way from 2002+ ?  At least that's what's implied from various catalogs if I want to order a seat for my '03 Monster.

On my 2003 M800Sie:

A = 9-3/4" (inside edge to inside edge)

B = 5-1/2" (1/2" gap at centerline)

Jeff
2003 M800Sie / 2004 BMW R1100S / 1981 BMW R100RS (Sold) / 1977 Kawasaki KE100 (1st Bike :))
http://ducatimonsterforum.org/index.php?topic=27788.0

Raux

#7
November 22, 2009, 09:38:38 AM
you'll also have to account for the angle of the seat. since the frames changed on the 3 generations (851,ST and new frames) each seat has a different angle of mounting. and of course the frame rails are most likely different. the way the hook in the front and where the seat latch point is as well.

geez, did i make this more difficult than it should be.

In the end.
A: width at front
B: width at rear of tank
C: frame width (at resting points on frame)
D: distance from B to latch point
E: distance from B to resting points
F: seat angle
G: front latch type and locations

stopintime

#8
November 22, 2009, 09:56:56 AM
I got 9 1/2 and 5 1/8 (with a 10mm centerline gap).
The seat is flexible where the measurements are taken, so this isn't exact. You'll figure it out [thumbsup]

While you're at it, take a look at these covers:   
http://hydroturf.com/products.php?cat=Seat%20Covers%20-%20Sport%20Bike&man=Ducati
252,000 km/seventeen years - loving it

Ducatl

#9
November 22, 2009, 09:04:54 PM
I'd like to see the bike this is going on.

NakedNFast

#10
November 23, 2009, 02:26:03 PM
Ill post a pic of the seat on the bike when i get the sub frame fab'd :) the seat I bought off ebay has a number on the bottom of it ... 595.1.026.1A if that means ne thing to any of ya? not sure what year it came off. Thanks for everyone's help giving me some measurements I expect the seat to work for my application if not ill just mod it to fit.. I will def keep u guys up to date on the build since I am incorporating a duc monster part ;)

NakedNFast

#11
November 23, 2009, 02:31:52 PM
Quote from: stopintime on November 22, 2009, 09:56:56 AM

While you're at it, take a look at these covers:   
http://hydroturf.com/products.php?cat=Seat%20Covers%20-%20Sport%20Bike&man=Ducati

THX FOR THE LINK! I am def gonna use these guys for the cover!

victor441

#12
November 23, 2009, 07:06:56 PM
Quote from: NakedNFast on November 23, 2009, 02:26:03 PM
Ill post a pic of the seat on the bike when i get the sub frame fab'd :) the seat I bought off ebay has a number on the bottom of it ... 595.1.026.1A if that means ne thing to any of ya? not sure what year it came off. Thanks for everyone's help giving me some measurements I expect the seat to work for my application if not ill just mod it to fit.. I will def keep u guys up to date on the build since I am incorporating a duc monster part ;)

FWIW you can download model and year specific Ducati parts manuals at http://www.ducati.com/en/bikes/service/maintenance.jhtml ...they are a great resource
Print
Go Up Pages1
User actions