|
Raux
Guest
|
 |
« on: July 25, 2010, 07:50:15 AM » |
|
Can you take a magnet and check to see if your rear subframe halves are steel or aluminum. also, can you take a picture of the back of the bike with the seat off? thank you. that is all  |
|
|
|
« Last Edit: July 30, 2010, 10:39:03 AM by Raux »
|
Logged
|
|
|
|
libertarian
New Member
 Offline
Posts: 15
|
|
« Reply #1 on: July 27, 2010, 03:35:52 PM » |
|
Aluminum. I can try to get a pic later, but it looks almost exactly like an 1100... Something specific you're looking for?
|
|
|
|
|
Logged
|
|
|
|
|
Raux
Guest
|
|
« Reply #2 on: July 27, 2010, 07:08:18 PM » |
|
i'm looking for any differences between the two specifically looking where and how the grab handles mount. ie are there new screw holes/location/bracing.
|
|
|
|
|
Logged
|
|
|
|
|
Raux
Guest
|
|
« Reply #3 on: July 30, 2010, 10:38:30 AM » |
|
ok grab handles arrived. 796 is different than 696. there is a new mounting point at the very end of the 796 subframes that is NOT on the 696.  |
|
|
|
|
Logged
|
|
|
|
libertarian
New Member
Offline
Posts: 15
|
|
« Reply #4 on: July 30, 2010, 11:01:49 AM » |
|
..And I was literally coming back from the parking lot to post a picture for you. Sorry about that. It's probably more like the 1100 than the 696, most of the rest of the back end is.
|
|
|
|
|
Logged
|
|
|
|
|
Raux
Guest
|
|
« Reply #5 on: July 30, 2010, 11:04:41 AM » |
|
could you still post those pics please. someone else might need them as well
|
|
|
|
|
Logged
|
|
|
|
libertarian
New Member
Offline
Posts: 15
|
|
« Reply #6 on: July 30, 2010, 11:18:01 AM » |
|
Side  Top  |
|
|
|
« Last Edit: July 30, 2010, 11:19:38 AM by libertarian »
|
Logged
|
|
|
|
|
Raux
Guest
|
|
« Reply #7 on: July 30, 2010, 11:31:10 AM » |
|
would you mind running out and taking a couple more. I need to see the underside of the back of the subframe. basically the end of the aluminum castings.
trying to figure out how many holes are on the underside of those castings
|
|
|
|
|
Logged
|
|
|
|
libertarian
New Member
Offline
Posts: 15
|
|
« Reply #8 on: July 30, 2010, 08:06:03 PM » |
|
I'll see what i can do in the morning, but most of that area is covered by the tail (or in my case, the tail chop)
|
|
|
|
|
Logged
|
|
|
|
|
Raux
Guest
|
|
« Reply #9 on: July 30, 2010, 08:16:16 PM » |
|
great thanks. specifically I'm looking for a photo of what is on the underside of this  |
|
|
|
|
Logged
|
|
|
|
|
Randy@StradaFab
|
|
« Reply #10 on: July 31, 2010, 05:28:03 AM » |
|
Part numbers for the 696 and 1100 frames are the same, so they must have done something different with the 796 if the grab handles don't mount the same.
|
|
|
|
|
Logged
|
|
|
|
M1100
Full Member
Offline
Posts: 224
Life is Good....
|
|
« Reply #11 on: July 31, 2010, 06:12:15 AM » |
|
Drat! Ducati Seattle called and the one they ordered for me won't fit (that is what Jon said).... bummer! |
|
|
|
|
Logged
|
Big Bear Chopper Sled Prostreet
Monster 1100
The artist FKA bbc chop
|
|
|
libertarian
New Member
Offline
Posts: 15
|
|
« Reply #12 on: August 02, 2010, 12:55:40 PM » |
|
here's the underside - in this picture, the left blinker is at the top of the frame. Hope this helps.  |
|
|
|
|
Logged
|
|
|
|
|
