powered by:
October 01, 2024, 06:27:31 PM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
:
Please Help
Home
Help
Search
Login
Register
Discussion Boards
Introduce Yourself
FAQs and Policies
General Monster Forum
Remembering our friends...in Memorium
Riding Techniques
Tutorials
Tech
Accessories & Mods
Gear
Racing & Trackdays
Stolen Motorcycles
No Moto Content
Board Tech Issues
Local Club Boards
BOMb
RCP
Sponsors
Valley Desmo Service
California Cycleworks
MotorcycleGear.Com
Monsterparts
Minor Sponsor Board
Sponsor Info
Flea Market
Monsters for Sale
Monsters Wanted
Other Bikes
Parts for Sale
Parts Wanted
Gear for Sale
Misc for Sale/Wanted
Ducati Monster Forum
>
Moto Board
>
Tech
(Moderator:
Speeddog
) >
m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
Pages: [
1
]
Go Down
« previous
next »
Print
Author
Topic: m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing? (Read 743 times)
paul rockwell
New Member
Offline
Posts: 5
m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
«
on:
May 16, 2016, 09:02:28 AM »
My slave cylinder started leaking and my clutch gave out. I went to a cycle shop and bought a slave cylinder off an early 2000s monster. My bike is a 1995 monster 900m. I put the slave on and bled. The clutch wont engage. I did research and read that pre 2000 bikes have actuator rod that doesnt stick out as far and that adding a 8mm ball bearing will cure this problem? Is this true? I dont want to mess up slave if I have to return it.
Logged
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78673
DILLIGAF
Re: m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
«
Reply #1 on:
May 16, 2016, 09:07:42 AM »
There were some aftermarket slaves that required the use of a ball bearing on some bikes, but 8mm sounds too big. I don't think it will fit inn the slave piston. I've also seen the ball wear into the piston.
You could get the longer pushrod.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
paul rockwell
New Member
Offline
Posts: 5
Re: m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
«
Reply #2 on:
May 16, 2016, 11:48:26 AM »
Thank you
Logged
Speeddog
West Valley Flatlander
Flounder-Administrator
Post Whore
Offline
Posts: 14813
RIP Nicky
Re: m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
«
Reply #3 on:
May 16, 2016, 01:08:35 PM »
The typical spacers are 8mm diameter, 10mm long.
Some are cupped on one end to fit the round ended pushrods.
Logged
- - - - - Valley Desmo Service - - - - -
Reseda, CA
(951) 640-8908
~~~ "We've rearranged the deck chairs, refilled the champagne glasses, and the band sounds great. This is fine." - Alberto Puig ~~~
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
Offline
Posts: 78673
DILLIGAF
Re: m900 clutch slave 1995 replace w early 2000 slave need 8mm ballbearing?
«
Reply #4 on:
May 16, 2016, 01:32:28 PM »
Quote from: Speeddog on May 16, 2016, 01:08:35 PM
The typical spacers are 8mm diameter, 10mm long.
Some are cupped on one end to fit the round ended pushrods.
Shows you where thought will get you.
Logged
"Once you accept that a child on the autistic spectrum experiences the world in
a completely different way than you, you will be open to understand how that
perspective
is even more amazing than yours."
To realize the value of nine months:
Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”
Pages: [
1
]
Go Up
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
Introductions
-----------------------------
=> Introduce Yourself
=> FAQs and Board Policies
-----------------------------
Moto Board
-----------------------------
=> General Monster Forum
=> In Memorium...Remembering our Friends
=> Riding Techniques
=> Tutorials
=> Tech
=> Accessories & Mods
=> Gear
=> Racing & Trackdays
=> Stolen Motorcycles
=> Random Cool Pics
-----------------------------
Kitchen Sink
-----------------------------
=> No Moto Content
===> Board Suggestions
===> Fixed Board Issues
=> Stella's Pop
-----------------------------
DMF Sponsors
-----------------------------
=> Valley Desmo Service
=> Ca-Cycleworks
=> New Enough.Com
=> Monsterparts
=> Minor Sponsors
=> Misc Info
-----------------------------
Local Clubs
-----------------------------
=> Monster Women
=> Ducati MOB
=> SoCal Monsters
=> CAM
=> OZ monsters
=> NorthWest
=> NEMHA
=> NYMMC
=> MHM
=> SoCO DOG
=> DFWM
=> MADDOG
=> MOCHA
=> THCM
=> AZDRA
=> M-ROC
=> Central Cal Monsters
=> DOCSF
=> MCMC
=> DDCM
=> DOCTOR
=> Hoosier Hooligans
=> OMHA
=> DOCIA
=> Rising Sun Ducatis
=> MCM
=> NMMR
=> MIA
=> Desmotropic
=> COW
=> MOTH
=> DesmOK
=> Bayou Country Ducati Riders
=> DeVal Mostro
=> Coastal Ducati Club
-----------------------------
Configurators and Calculators
-----------------------------
=> Valve Shim Calculator
Loading...
SimplePortal 2.1.1