What did you just buy for your Ducati?

[Rudemouthsky]

A new 7" headlight to use with my Corse Dynamics mounting bracket. I'm hoping this will be suitable to house an LED Truck-Lite or JW Speaker in the future. The light that Motowheels sells with their kit is crap, some awful looking Drag Specialties Hardley light.

[Privateer]

Because they were worn out or you got a diff brand?

well my camera had trouble focusing..






was kind of a pain because I had to buy a new spark plug wrench for the new ones.  not sure what's up with that.

[msuxplant]

Clip one an carbon fiber belly pan for my S4R.  Looks soooo much meaner and faster in my garage I just might have to start er up!

[Rudemouthsky]

Clip one an carbon fiber belly pan for my S4R.  Looks soooo much meaner and faster in my garage I just might have to start er up!

Pics are required in this thread.

[caperix]

pic???

Sorry for the delay, here is a pic of the new master cylinders.




They also came with a set of new resevour caps that I am unsure of the brand

[Rudemouthsky]

Sorry for the delay, here is a pic of the new master cylinders.




They also came with a set of new resevour caps that I am unsure of the brand

Purdy...almost makes me wanna re-think getting the titanium colored SBK masters + billet reservoirs.

[TitanMonsterS4R]

Purchased mini oval turn signals and Barracuda Tiger taillight from my our lovely board sponsor MonsterParts.

[DexterMorgan]

Just ordered a Carbon Fiber rear hugger from Jeff at MonsterParts.         
Jeff is AWESOME!!!


Also ordered a BMC air filter. 

[Skybarney]

Just ordered a Carbon Fiber rear hugger from Jeff at MonsterParts.          
Jeff is AWESOME!!!

Quick thoughts, since I have the same hugger.  Without doing this the hugger rattles about a bit.

I put little o-rings on the top and bottom of the three bolts used to install the hugger.  One protects the top of the carbon the other seals the hugger against the swingarm.  This required installing the bolts before I installed the hugger as the underside o-ring will keep the bolts in place.

[DexterMorgan]

Thanks for the tip man.  Did you just use small rubber o-rings?  Do you know what size those bolts are? M5, m6 maybe?

[Skybarney]

I don't remember the bolt size.  Yup just small o-rings.  I have a 10.00 kit from Harbor Freight and it has a ton of different sizes to choose from.  It has saved my butt many a time.

[bob795]

Motobatt waterboy charger.

It comes with a pigtail and I just finished installing the pigtail. Geez, taking off the gas tank to access the battery ... I didn't completely remove the tank though. The best thing is there's no unused bolt or nut lying around after I finished the job

[DexterMorgan]

Just ordered my POWER COMMANDER V!!!  I am super excited for this one to get here.       

Also ordered 1/4" and 3/8" Spinner T-handle tools.  Tax refunds are dwindling!! 

[Rudemouthsky]

Cycle Cat clip ons from eBay. Seller claims "perfect condition" but I'm dubious. Plan on stripping, polishing, and re-anodizing.

[Rudemouthsky]

Ended up passing on the CC clip ons...didn't trust the seller. But then I saw this, and just had to have it for my build...a brand...spankin'...NEW machined clutch side housing. Think I'll go with a satin black powdercoat for the cases, leave the fresh factory aluminum finish on this piece, use my MPL Brushed alloy pressure plate and a Motowheels "flow" clutch cover in black. Reallllly stoked on this for $150...