Motogadget loom project

[ducatigirl100]

Did you find a source for coil on plug coil packs for the Air cooled motor?  The only thing I can find are Accekk coils for twin cam Harleys, and they lok a little too bulkey to fit the monster cyl head.

I'll may use car one's. ....    I'm looking onto specs to find one that would work...  futur update soon 

[koko64]

Those coils might stand out too far at an angle on the air cooled motor? Maybe the Exactfit will give a big spark but are still very light, much lighter than the Dynas or Accel. If you find very small/or short stick coils it would be a great find. I know the Accel from my Harley days. I wonder if MSD make something special you need? Have you checked the Electrex site?

You tell R1 that he has to treat you right or the Ducatisti Mafioso will come!

[ducatigirl100]

I've got the bike back this week .... yepp... winter 

I've decided to put the M-unit beside the airbox.....

My  R1 BF made the bracket 

[Duck-Stew]

I have NO idea why I'm *just now* reading this thread, but WOW!  Very nicely done with everything you've done!

Having wired up 6 MotoGadget units onto customers bikes through out the years, the quality is first rate... 

I did use a MotoGadget Tiny once, but I mounted it where the original key cylinder went in order to leave the ENTIRE stock gauge area blank...  (I hid the key cylinder under the tank.)  Was a very clean installation...

Best of luck with finishing it all!  I can't wait to see what you do next. 

[ducatigirl100]

I have NO idea why I'm *just now* reading this thread, but WOW!  Very nicely done with everything you've done!

Having wired up 6 MotoGadget units onto customers bikes through out the years, the quality is first rate...  

I did use a MotoGadget Tiny once, but I mounted it where the original key cylinder went in order to leave the ENTIRE stock gauge area blank...  (I hid the key cylinder under the tank.)  Was a very clean installation...

Best of luck with finishing it all!  I can't wait to see what you do next.  

Thanks    

I alredy add the intention of putting the tiny where the sterring lock is ....
I have the M-lock also

Do you have some pics of the tiny that you've installed ?

[Rudemouthsky]

I have NO idea why I'm *just now* reading this thread, but WOW!  Very nicely done with everything you've done!

Having wired up 6 MotoGadget units onto customers bikes through out the years, the quality is first rate... 

I did use a MotoGadget Tiny once, but I mounted it where the original key cylinder went in order to leave the ENTIRE stock gauge area blank...  (I hid the key cylinder under the tank.)  Was a very clean installation...

Best of luck with finishing it all!  I can't wait to see what you do next. 

+1. Really, really impressive work Ducatigirl. Been lurking this thread for awhile now. 

[MotoPsycho]

Very clean installation. I did a Motogadget Motoscope Pro on Edgar and the wiring I did looked remedial compared to that work. This gives me motivation to redo what I have.

One question though about my integrated tail light. On the M-Unit, the way it reads in their literature, the turn signals act a running lights but is configurable. That's the only thing that's kept me from getting one.  Can this be confirmed ?

[ducatigirl100]

Very clean installation. I did a Motogadget Motoscope Pro on Edgar and the wiring I did looked remedial compared to that work. This gives me motivation to redo what I have.

One question though about my integrated tail light. On the M-Unit, the way it reads in their literature, the turn signals act a running lights but is configurable. That's the only thing that's kept me from getting one.  Can this be confirmed ?

Signal ligths can be used as "navigation lights"  

On the setup menue's of the M-unit you can set them  at different brigthness  ex: 10%  - 20% - 30 % or 0% ( default setup)   

Personnally I'll do the default setup because I have a motodynamics integrated tail ligth
  
Also you can setup hazard's  

[MotoPsycho]

I found this: http://www.wirecare.com/products.asp?prodline=DPP
Might come in handy for the next person to want to take this on.

[ducatigirl100]

This 

Deutsch connectors are great

Also    having a higth quality crimping tool is a must 

[MotoPsycho]

On the motoscope tiny, does is have the orange bus wire to hook to the breakout box ?

[ducatigirl100]

On the motoscope tiny, does is have the orange bus wire to hook to the breakout box ?

No it dosen't have it 

   althoug it would be great to have a breakout box instead of 
soldering all the wires needed  to connect it....

There was some crimp's in the box that it came in but I didint use them

[ducatigirl100]

Now the back of the bike is  cleaner

I'm finising the installation this weekend  ... so more pics to come

Leson's learned
1-dont do the loom in advance like i did
2- hook up the M-lock or key ignition first

More to come.....

[lazylightnin717]

That looks great!

 

[duccarlos]

Now the back of the bike is  cleaner

I'm finising the installation this weekend  ... so more pics to come

Leson's learned
1-dont do the loom in advance like i did
2- hook up the M-lock or key ignition first

More to come.....

Way cleaner! Looks great!