Ducati Monster Forum

powered by:

December 22, 2024, 09:11:29 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: No Registration with MSN emails
 
   Home   Help Search Login Register  



Pages: 1 2 3 [4] 5 6 ... 11   Go Down
  Print  
Author Topic: Marks (now solo) M1100 (mis) adventures!  (Read 25379 times)
Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #45 on: January 24, 2023, 04:32:44 PM »


Question:  Referencing the 2V air cooled motors in general... the standard service interval is 7500mi, do the valves really go out of tolerance that much in 7500mi?

I have been told in the past that the 1st valve check is the most important; after that things seem to calm down and as the miles click off, future valve adjustments require less adjusting.

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #46 on: January 26, 2023, 05:53:24 PM »

Well boys, I have run into my first head-scratcher; I cannot get the swingarm shaft to even act like it wants to budge! I have removed the footrests, removed the wedge shaped bolt on the right side and the snap ring, also on the right side.

This is what the right and left sides look like now:

20230126_193632 by Mark Hanis, on Flickr

20230126_193552 by Mark Hanis, on Flickr

I am trying to drive the shaft from the right (clutch) side through to the left (chain) side. When I strike the shaft with a rubber mallet I get a HARD stop, it is like it has NO interest in moving.

Do I need to get something more solid and give it a go?

Oh, the engine should be ready for pickup this weekend!

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #47 on: January 27, 2023, 03:29:49 AM »

I'd use a regular hammer with a block of wood, or ideally a large diameter brass drift to break it free. A rubber mallet won't impart enough shock.
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #48 on: January 27, 2023, 07:21:29 AM »

That was my thinking but I wanted a second opinion before I leaned into it a bit!

Will I need to continue to drive the shaft through the swingarm/engine case, or once I get it pushed out the left side a little will it simply pull out from that side?

Another way of asking that; what size punch do you think I'll need? I can order one from work and I don't want to pay for a set as I can buy individual ones, I just need to know what size.

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
koko64
Post Whore
******
Offline Offline

Posts: 15711


« Reply #49 on: January 27, 2023, 02:13:30 PM »

Workshop has a selection of timber off cuts. Special tools.
Logged

2015 Scrambler 800
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #50 on: January 27, 2023, 03:06:43 PM »

That was my thinking but I wanted a second opinion before I leaned into it a bit!

Will I need to continue to drive the shaft through the swingarm/engine case, or once I get it pushed out the left side a little will it simply pull out from that side?

Another way of asking that; what size punch do you think I'll need? I can order one from work and I don't want to pay for a set as I can buy individual ones, I just need to know what size.

Mark
You may need to. Hard tellin'. I've heard tales of very rusty swing arm pivot shafts. I hear my SBK had one that was difficult to remove. I also hear pressure washing will drive water past the seals and contribute to rust.

Measure the end of the shaft and order a length of brass bar 1/8" smaller, and long enough to go all the way through.
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #51 on: January 27, 2023, 05:27:20 PM »

I also hear pressure washing will drive water past the seals and contribute to rust.


I'm not a damn animal!!   Grin

But I do have a LOT of time spent riding in the rain. And HARD rain at times.

So, I am getting no movement at all using a hammer and a block of wood (what I have available). It seems that a brass punch as big as I need it is not going to be readily available. What are your thoughts on getting a brass hammer, setting that against the shaft and striking the brass hammer with another hammer?

Additionally, is it OK to hit the area with some liquid wrench and let it sit up?

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #52 on: January 27, 2023, 06:41:34 PM »

I'm not a damn animal!!   Grin

But I do have a LOT of time spent riding in the rain. And HARD rain at times.

So, I am getting no movement at all using a hammer and a block of wood (what I have available). It seems that a brass punch as big as I need it is not going to be readily available. What are your thoughts on getting a brass hammer, setting that against the shaft and striking the brass hammer with another hammer?

Additionally, is it OK to hit the area with some liquid wrench and let it sit up?

Mark
Yes, and yes. It'll take whatever it takes.

The only downside to the brass hammer is if it needs to be driven after you break it loose.

Brass bar not available?... https://smile.amazon.com/Pieces-BRASS-SOLID-ROUND-Lathe/dp/B01F80WOZU/ref=sr_1_4?crid=3GARVCQCN81VX&keywords=3%2F4+brass+bar+stock&qid=1674873560&sprefix=3%2F4+brass+bar+%2Caps%2C113&sr=8-4
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #53 on: January 28, 2023, 11:15:52 AM »

Thanks for the link, I am going to order a rod. I knew I could source what I needed; I was just hoping to find something that I needed OFF THE SHELF. I did manage to find a brass hammer, so, a bit of heat, some PB Blaster and the brass hammer has yielded movement! Not much, maybe 1/8".

The mechanic at the shop suggested moving the rod back and forth, as opposed to trying to keep pounding one direction. After he said that it seemed so obvious! Yet I would have done EXACTLY what he said not to do. But based on what I am feeling now, I think I'll have to get a piece of round bar to get it extracted.

I'll keep ya posted.

And the engine is in my garage and that feels really good!

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #54 on: January 28, 2023, 03:18:33 PM »

Plan or replacing the bearings/seals.
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #55 on: January 28, 2023, 06:26:02 PM »

Plan or replacing the bearings/seals.

That has been discussed.

So, major victory, minor setback:

First, the victory:

20230128_200641 by Mark Hanis, on Flickr

One I put a couple of heat cycles, PB Blaster and muscle it started to move pretty freely, so out it came!

Now the setback:

20230128_200657 by Mark Hanis, on Flickr

I tried (unsuccessfully) to remove the bottom bolt on the shock. I failed. I supported the engine from below and went back to the top bolt and was able to release it.

Now my problem is this bottom bolt; it is bound up pretty good! It doesn't want to move either way. I'd be happy enough just screwing it back in, but it is reluctant to go for some reason. Have I FUBAR'd?

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #56 on: January 28, 2023, 06:41:28 PM »

Sometimes...shocking with either an impact wrench, or hammer driver can create progress.
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Mhanis
Hero Member
*****
Offline Offline

Posts: 1308



« Reply #57 on: January 28, 2023, 07:25:05 PM »

I am hesitant to use an impact driver going IN, but if the bolt is not out then it is still captured in the threads so I don’t have to worry about cross-threading, right?

Mark
Logged

I ride a GS scooter with my hair cut neat.

Pete Townshend

2009 M1100 72,000+ miles- and climbing
2015 Suzuki TU250X 13,000+ miles GONE!
koko64
Post Whore
******
Offline Offline

Posts: 15711


« Reply #58 on: January 29, 2023, 12:15:23 AM »

That recessed section around the bolt should hold some anti seize liquid. Worth filling it with the swingarm on its side overnight. Nothing to lose. An impact driver should work and will damage the Allen head so you would replace the bolt, but a rattle gun will chew it out much worse.
Logged

2015 Scrambler 800
ducpainter
The Often Hated
Flounder-Administrator
Post Whore
*****
Offline Offline

Posts: 78835


DILLIGAF


« Reply #59 on: January 29, 2023, 04:27:05 AM »

I am hesitant to use an impact driver going IN, but if the bolt is not out then it is still captured in the threads so I don’t have to worry about cross-threading, right?

Mark
You're trying to break a mechanical bond. No harm in going both directions.
Logged

"Once you accept that a child on the autistic spectrum experiences the world in
 a completely different way than you, you will be open to understand how that
 perspective
    is even more amazing than yours."
    To realize the value of nine  months:
    Ask a mother who gave birth to a stillborn.
"Don't piss off old people The older we get, the less 'Life in Prison' is a deterrent.”


Pages: 1 2 3 [4] 5 6 ... 11   Go Up
  Print  
 
Jump to:  


Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder
Valid XHTML 1.0! Valid CSS!
SimplePortal 2.1.1